Just how do you really feel in relation to Installing A Bathtub?
![Tools You Need to Install a New Bathtub](https://img.hunkercdn.com/375/clsd/getty/73a23e9186ae4eb9a0305ab781aefdf8.jpg)
Setting up a bathtub isn't exactly rocket science, however it does require strong plumbing, carpentry, and sometimes, tiling abilities. Changing an old bath tub with a brand-new one is additionally a moderately hard project. If the old tub is easily accessible, the project can move immediately; if you have to open up a wall to get rid of the old bathtub and place the new bathtub, the task is a lot harder. In either instance, the job is within a house handyman's skills, although you will certainly need a helper to vacate the old bathtub as well as set in the brand-new one. Make sure you have actually qualified yourself for the work as well as fit trying it. Rather than employing a contractor to take over a halfway-completed project, it is far better to consider employing one before you start. Possibilities are you may require a specialist plumber to make tube links.
This write-up will assist you install a new tub in your washroom if you have already bought a new bathtub as well as do not need to transform the setup of your previous supply of water pipelines.
Your devices and also material list should consist of the following:
Planning for the Setup
Firstly, the sustaining frame supplied with the bath needs to be fitted (if required) according to the producer's directions. Next, fit the taps or mixer to the tub. When fitting the tap block, it is very important to make certain that if the tap includes a plastic washer, it is fitted between the bath and also the faucets. On a plastic bathroom, it is likewise practical to fit a supporting plate under the faucets device to prevent pressure on the bath tub.
Fit the flexible tap connectors to the bottom of the two taps using 2 nuts and olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet with the hole in the bath. Utilize the nut supplied by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Ensure you utilize every one of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach all-time low of the overflow tube in a similar manner.The bath ought to now be ready to be fitted in its final placement.
Removing Old Taps
If you require to change old faucets with new ones as a part of your installment, then the first thing you ought to do is disconnect the water. After doing so, activate the faucets to drain any type of water staying in the system. The process of removing the existing taps can be quite bothersome as a result of the limited gain access to that is commonly the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipelines to the taps. Have a fabric all set for the continuing to be water that will certainly come from the pipelines. When the supply pipelines have been eliminated, use the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single faucets from turning throughout this procedure. As soon as the faucets have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any kind of old securing substance.
Before moving on to fit the new taps, contrast the pipe connections on the old taps to the new taps. If the old taps are longer than the new taps, after that a shank adapter is required for the brand-new faucets to fit.
Setting up the Tub
Utilizing both wood boards under its feet, place the bath tub in the called for setting. The wooden boards are useful in evenly spreading the weight of the bathtub over the area of the boards instead of concentrating all the weight onto 4 small factors.
The following goal is to make sure that the tub is leveled all round. This can be attained by inspecting the spirit level and adjusting the feet on the bath tub up until the level reviews degree.
To mount faucets, fit the bottom of the furthest versatile tap connector to the appropriate supply pipe by making a compression sign up with; after that do the very same for the other tap.
Switch on the water supply and also inspect all joints as well as brand-new pipework for leaks and tighten them if essential. Fill the tub and likewise check the overflow electrical outlet and the regular electrical outlet for leakages.
Ultimately, deal with the bath paneling as described in the manufacturer's user's manual. Tiling and also sealing around the bath tub should wait up until the bathtub has been used a minimum of once as this will settle it into its final setting.
Suitable New Taps
If the tails of the brand-new taps are plastic, then you will certainly require a plastic port to avoid damage to the thread. One end of the port fits on the plastic tail of the tap as well as the other end gives a link to the current supply pipes.
If you require to fit a monobloc, after that you will require lowering couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin ensuring that the washers remain in place in between the faucet and the sink. Secure the tap in place with the manufacturer given backnut. When the faucet is safely in place, the supply pipes can be linked to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with regular tap adapters. The previous type must be connected to the faucet ends initially, tightening just by hand. The supply pipelines can later be connected to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the area where the bath meets the ceramic tile, it is needed to secure the joins with a silicone rubber caulking. This is necessary as the installation can relocate sufficient to split a stiff seal, creating the water to permeate the wall in between the bathroom and the tiling, leading to difficulties with moisture and possible leaks to the ceiling below.
You can choose from a range of coloured sealers to blend in your components and installations. They are marketed in tubes and cartridges, and also can sealing spaces approximately a width of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with spins of drenched newspaper or soft rope. Keep in mind to constantly load the bath tub with water prior to sealing, to enable the activity experienced when the tub is in use. The sealer can fracture relatively very early if you do not take into consideration this motion before securing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise conveniently available on the market. It is a good idea to fit the floor tiles making use of water-resistant or water-proof sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
![A Step-by-Step Guide to Installing a Bathtub](https://i0.wp.com/www.projectsmallhouse.com/blog/wp-content/uploads/2020/01/OVE_Decors-980208275-Ruby.jpg?resize=500%2C347&ssl=1)
Do you like more info about A Step-by-Step Guide to Installing a Bathtub? Put feedback down the page. We will be delighted to see your thinking about this content. In hopes to see you back again in the near future. Sharing is caring. Helping others is fun. Thanks so much for your time spent reading it.
Click On This Link